Cables While Knitting in the Round

If you are knitting a cabled pattern in the round, it’s sometimes difficult to see/know when you are on a cable round as opposed to when you are knitting back and forth. There are a few tricks to being able to count the rounds which I’ve illustrated below.



This is my preferred method and what I think is the easy method.

Smooth Circular Joins

One way to make a smooth join when knitting in the round is to cast on 1 extra stitch. When joining the circle, knit the first and last stitches together.

Reading and Knitting Difficult Patterns

If you have a difficult pattern and lose your place when going from pattern or chart to your knitting, record the pattern steps on audio so you can listen and knit rather than finding your spot on a written pattern.

Counting Rows

It’s sometimes hard to count the number of rows in stockinette, especially if you are using a little bit of a fuzzy yarn. Instead, count rows from the back/purl side and stretch it out a bit so you can easily see the rows.

Chart Reading

If you are moving up to the challenge and knitting a complicated lace or fair isle pattern, mark your chart with colored vertical lines between the obvious patterns. Then use corresponding colored embroidery floss or colored markers (or even colored paper clips) in your knitting so you can see at a glance where you are in the pattern.

Picking Up Tinked Stitches

If you need to “tink” or rip back your knitting in stockinette stitch, make sure the right leg of each stitch is toward the front side of your needle when you pick up those stitches.

Increase in Ribbing

When making increases in ribbing (like from the bottom band to the body of a sweater), use a kfb or bar increase and do the increase in a knit stitch which is immediately followed by a purl stitch. This will make the increase nearly invisible. Then make your first stockinette row a purl row and that will really hide the increases.

Trimming Fringe

To straighten fringe before trimming, comb it out using a wide tooth hair pick type of comb.

Finding Yarn Ends

To easily find the tail end of your yarn skein once you’ve started using the yarn, use a bobby pin. Clip the end of the yarn with the bobby pin and push it into the skein. Totally secure and easy to find.

Uneven Stockinette Stitches

Use one size smaller needle on the purl side of stockinette stitches to make knitting more even overall and be more like machine knitting. Purl stitches take just a smidge more yarn and 1 needle size smaller will compensate for the difference. If you aren't sure if you have uneven stockinette stitches, turn your work over and stretch it vertically a bit. If you have "channels" showing every 2 rows, you need to use this tip.

Cast-On at End of Row

If you are instructed to cast on at the end of a row in the middle of your knitting, there are several ways to do it. You could use a knitted cast-on or you could insert a crochet hook in the edge stitch in the 2nd row below the last stitch that is on your needle. Make a loose chain the number of stitches required to cast on. Remove hook and insert free needle into the last loop to make 1 stitch. Pick up a stitch in each loop (back where you started the cast-on) and then continue to knit across.

Placing Holding Stitches on Ribbon

If you want to try on a garment, place the stitches on a piece of satin ribbon and tie the ends together. So if you are trying on a top down sweater, put the body stitches on the ribbon leaving plenty of length, tie the ends of the ribbon together and try on the sweater. To make it extra easy, put those stitches back on a needle a few sizes smaller remembering to knit onto the right sized needle when you start knitting again.

Cable Needles

If you still have the old style plastic hair picks (or beg a couple from your hairdresser), they make good cable needles. You can push them into the yarn while holding the cable stitches and while you store the needles between making cables.

Center Wound Yarn Balls

Another way to make a center pull yarn ball: Start with medicine pill bottle, put end of yarn inside and snap the lid closed. Wind yarn around bottle keeping it below the bottle cap. When finished, remove bottle releasing the end of yarn and pull from center. The ball will stand and not roll when using.

Know Your Stash

For those of you detailed enough to upload your stash on Ravelry, you can save your listing to an Excel spreadsheet by clicking the small Excel icon on the right hand side (next to the Search button) of the stash section in your Ravelry notebook. It makes a nice, compact printout to know what you already own. An example is shown.

Buttonbands

To stabilize the button band of a cardigan, sew clear small buttons on the inside of the band behind the decorative buttons that are on the outside of your cardigan

Yarn Bobbins

To make yarn bobbins, cut 2”x4” pieces from plastic canvas. Then cut a notch in both the top and bottom of the piece. Wrap your yarn around the canvas using the notches as guides. You can secure the ends of the yarn through the holes in the plastic canvas.

Easy Fair Isle

If you have a hard time knitting Fair Isle using both hands, use this easy method instead. Knit one round using just color A and slip the other stitches with yarn in back making sure they are stretched out just enough to lay flat. Then knit the next round using just Color B and slip the color A stitches purlwise with yarn in back. Two rounds knitted this way covers 1 row in a charted design.

Neater Cuffs on Sleeves

To make neat cuffs on a sweater that is knit flat, either knit the sleeves down to the cuffs or use a provisional cast on and knit from the top of the cuffs to the top of the sleeve. Sew the seams using a mattress stitch. Then pick up the cuff stitches and knit in the round using double pointed needles or 2 circulars so you have a seamless cuff.

Slip Stitch Edges

Use a slip stitch as a decorative front edge on sweaters or the edge of scarves and afghans but never use it where you are going to sew a seam such as on sweater front and back or sleeve pieces. It’s not a strong enough edging to hold a seam stable.

Long Tail Cast-On

The most common cast on method is the long tail. To make sure you have enough yarn, use the general rule of 4 times the length of the hem of whatever you are knitting as your guide.

Yarn Storage

Short of yarn storage space? Use fish stringer lines and use the snap hook part of the chain to hang yarn skeins.

Bindoff

To keep from having a pointed nub at the end of your cast off stitches (especially when making scarves), don’t work the last stitch at all. Just slip the last stitch and then finish by pulling the yarn through that stitch and weaving it to hide the tail.

Bulky Wool Yarn Joining

If you need to join bulky wool yarn, use needle felting tools to marry the ends together so they felt together. You’ll save length, eliminate knots, and give the project a seamless look.

Felting and Shaping

After felting an item, if you need to shape it, steam it. Steam, stretch and shape and re-steam if needed. It’s the washing agitation and shock of cold water that actually felts and shrinks an item, not the steam.